Service available now · 50 states Mon–Sun · 7AM–9PM EST
Installation & Setup Refrigerator

Liebherr Ice Maker: First Start and Turning It On

TL;DR: Switch on a Liebherr ice maker from the display or menu once the water source is ready and the freezer has cooled; the key sequence is in your manual. Expect slow ice on day one and throw away the first batches.

Updated Nov 16, 2026 5 min read
TL;DR: Switch on a Liebherr ice maker from the display or menu once the water source is ready and the freezer has cooled; the key sequence is in your manual. Expect slow ice on day one and throw away the first batches.

If you searched “liebherr how to turn on ice maker”, the short answer is that the IceMaker is switched on from the appliance’s own display or menu, and it only starts once the water supply is ready and the freezer has cooled down. The exact keys differ by model, so your owner’s manual has the button sequence. This guide covers what has to be in place before you switch it on, what to expect on the first day, and why the first batches should not go into a glass. It does not cover connecting water or any plumbing work, which belong to an installer.

Where it is switched onThe display or menu; the key sequence is in your owner’s manual
Water sourceA household water line or a tank you fill, depending on the model
Freezer must beCold enough that water in the mold can freeze
First batchesDiscard them; air and filter dust need to flush out
First dayIce is slow while the system comes up to temperature

How do you turn on the ice maker in a Liebherr refrigerator?

On a Liebherr with an IceMaker the on and off setting is in the display, next to the freezer temperature. Our guide on how a Liebherr ice maker works describes the control as an on and off setting plus the freezer temperature. Which keys you press, and in what order, depends on the model, so read the section of your owner’s manual on the IceMaker. Our ice maker troubleshooting page notes that the IceMaker can be turned off by accident, which is why it is the first thing to check when a new unit makes no ice.

Switching it on does not make ice immediately. The ice maker waits until the freezer is cold enough, then opens its water valve for a short, timed fill, freezes the water in the mold, releases the cubes and repeats. What you will see first is nothing, then a small amount of ice. That is normal.

What has to be ready before you switch it on?

Three things: the refrigerator has been installed and has run long enough to be cold, the water source is ready, and the IceMaker setting is on. Our guide on the first start-up of a new Liebherr walks through standing the cabinet upright for the period your manual states, a grounded outlet without an extension cord, and leaving the door closed on the first day. Do the cabinet first and the ice maker second.

The water source depends on the model. A plumbed unit takes water from a household cold water line through a supply tube and a shutoff valve, and many installations also have a filter in the line. A tank model draws from a reservoir you fill and stops when the tank runs dry. Check which one you own, because the first-start check is different. A tank model usually just needs water in the tank, while a plumbed model needs an open valve and a line that is not kinked. Connecting or changing a water line is plumbing work, so leave it to the installer.

A hand near a tray of ready ice inside an open freezer drawer of a refrigerator
The first batches are slow and should be thrown away.

What should you expect on the first day?

Our ice maker page notes that ice is slow for the first day after installation, and that a freshly emptied bin takes hours to refill. During that time the freezer is still pulling down to its set temperature, so the mold cannot freeze water quickly. A freezer that is still warming or cooling is not ready to make ice. The compressor will also run almost constantly on day one, which is normal and not a reason to change settings.

Set the freezer temperature once and leave it. Opening the freezer door repeatedly to check for ice lets warm air in and slows everything down. Our guide on Liebherr temperature settings lists sensible starting points. The manual states how long the unit needs before you load it with food.

Why should you throw away the first batches?

Our ice maker cleaning and clear ice pages both say to discard the first batches after a new filter or after plumbing work. The line has air in it, and a new filter sheds a little carbon dust at first, and neither belongs in a drink. The same applies to a brand new installation, where the supply line has never been run. Throw away the first few harvests, then taste a cube before you serve it. Our water filter replacement guide covers what to do when the filter is fitted later.

When the ice is cloudy, small or tastes of the cabinet, that is usually water quality, filter age or ice sitting in the bin, not a fault. Our clear ice tips go through those habits, and the ice maker cleaning guide gives a simple routine for the bin.

When should you call a technician?

If the IceMaker is switched on, the water source is ready, the freezer is cold and there is still no ice after a day or two, our ice maker troubleshooting guide lists the checks in order. Beyond those, the inlet valve or the ice maker module may have failed, which is a parts repair for a technician. Do not open panels or work on the water connection yourself. If you see water pooling near the unit or around an electrical outlet, switch off the breaker at the panel while standing on a dry floor, and do not pull a plug from a wet outlet.

We are an independent repair company, not the manufacturer. Our Liebherr refrigerator repair page explains how a visit works, and you can schedule a visit online.

Frequently asked questions
How do I turn on the ice maker on a Liebherr refrigerator?
Use the IceMaker setting in the appliance’s display or menu. The key sequence differs by model, so follow the IceMaker section of your owner’s manual.
Why is my new Liebherr not making ice yet?
The freezer may still be cooling down, the IceMaker may be switched off, or the water source may not be ready. Ice is slow for the first day, so give it time before you suspect a fault.
Do I need to throw away the first ice?
Yes. Discard the first batches after installation or a filter change, because air in the line and loose filter dust need to flush out.
Does my Liebherr use a water line or a tank?
It depends on the model. Check your owner’s manual. If you are unsure, book a visit and we will confirm it on site.

Schedule Liebherr
appliance repair

Experienced technicians in all 50 US states. Average response within 24 hours.

  • Experienced Liebherr specialists
  • Genuine OEM parts
  • 30-day labor warranty
  • Upfront pricing
Need professional help?

Book experienced Liebherr
appliance repair

On-site diagnostics, genuine OEM parts, 30-day labor warranty. Service in all 50 US states.